hp-support-head-portlet

Actions
Loading...

HP Customer Support

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...

hp-concentra-wrapper-portlet

Actions
Loading...

HP and Compaq Desktop PCs - Motherboard Specifications, MS-6577 v4 (Gamila 2)

Motherboard specifications table
Motherboard Description
  • Motherboard Manufacturer's name - MSI MS-6577 v4.0 GL6E
  • HP/Compaq name - Gamila 2
Processors
  • Socket 478
  • Pentium 4 HT Northwood
  • Celeron Prescott and Northwood
  • Maximum approved processors:
    • 3.06 GHz (533 MHz) Celeron
    • 2.80 GHz Pentium 4
Chipset
  • 845GV
Front Side Bus (FSB)
  • 400/533 MHz
Memory
  • Two DDR DIMM (184-pin) sockets
  • Maximum memory: 1 GB
  • PC2700/PC2100
Audio
  • Down (on motherboard) AC97 (Realtek ALC658 chipset)
Graphics
  • Integrated
LAN
  • Realtek RTL8101L 10/100 Mbps Fast Ethernet Controller
Expansion Slots
  • Two PCI
I/O Ports
  • Rear
    • VGA
    • Two PS/2
    • One Parallel
    • One Serial
    • Four USB 2.0
    • One IEEE 1394
    • One RJ-45 LAN
    • Line in, Line out, Microphone in
  • Other
    • Two USB 2.0
    • One IEEE 1394
     note:
    Not all USB ports may be available externally for customer use; see model specifications
Feature Codes
  • G-graphics down (on motherboard)
  • L-LAN down (on motherboard)
  • E-1394 down (on motherboard)
  • 6-6 speaker mode (Dolby 5.1)
Motherboard layout and photos
Figure : Layout View
Motherboard Photos
Figure : Overhead View
    Figure : View of back panel connectors
  1. PS/2 mouse
  2. Parallel port
  3. IEEE 1394 connector
  4. RJ-45 connector
  5. Line in jack
  6. Line out jack
  7. Microphone jack
  8. USB 2.0 connectors
  9. USB 2.0 connectors
  10. VGA connector
  11. Serial connector
  12. PS/2 Keyboard
Clearing the CMOS settings
The Clear RTC RAM (3-pin JBAT1) jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. It also allows clearing of date, time, and system parameter memories in CMOS, by erasing the RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, including system setup information.
 caution:
Do not change any jumper setting while the computer is on. Damage to the motherboard can result.
  1. Turn off the PC and unplug the power cord.
  2. Move the JBAT1 jumper from pins 1-2 (normal) to pins 2-3 (clear CMOS).
  3. Keep the JBAT1 jumper cap on pins 1-2 for 5 to 10 seconds, then move it back to pins 1-2.
  4. Plug in the power cord and turn on the PC.
  5. Press F1 as the PC starts to enter BIOS setup and change the BIOS settings.
Clearing the BIOS password
  1. Turn off the PC and unplug the power cord.
  2. Remove the JPWD1 jumper cap.
  3. Press F1 as the PC starts to enter BIOS setup.
  4. Clear or reset the BIOS password.
  5. Save the BIOS settings and turn off the PC.
  6. Reactivate BIOS password checking by replacing the JPWD1 jumper cap.

hp-feedback-input-portlet

Actions
Loading...

hp-online-communities-portlet

Actions
Loading...

Ask the community!


Support Forum

Support Forum

Join the conversation! Find Solutions, ask questions, and share advice with other HP product owners. Visit now


hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
United States

hp-detect-load-my-device-portlet

Actions
Loading...