HP DesignJet 700 Printer - Product Specifications

The connector on the printer is 36-pin female.

Most existing parallel cables support Bitronics communication, but for use with this printer, the cable MUST meet the specification in the following table:

The connector on the printer is 25-pin female.

The printer is configured as DTE (data terminal equipment).

Data is transmitted on Pin 2 and received on Pin 3.

(1) CAD drawings only and HP media only.

note:

See also Supplies Source catalog and (in Europe and U.S.A.) Media Reference Guide.

note:

From time to time, new media types may become available. For up-to-date information, please contact your HP dealer or local HP Sales and Support Office.

This table is calculated with normal margins. Plotting area equals media size minus margins.

This table is calculated with normal margins. Plotting area equals media size minus margins.

This table is calculated with normal margins. Plotting area equals media size minus margins.

(Maximum accumulated error)

_0.38 mm (0.015 inch) or _0.2% of the specified vector length, whichever is greater, at 23 degrees C (73 degrees F), 50-60% relative humidity, on HP Matte Film.

HP-GL (7586B), HP-GL/2, HP RTL, PJL, PostScript (optional)

Replaceable print cartridge(s) have been used in your printer, greatly reducing its user maintenance requirements, as these are the components that experience the greatest wear and tear.

Cleaning is limited to the outside of the machine. Use a damp sponge or a soft cloth and household cleaner.

  warning:

To avoid an electric shock, make sure that the printer is switched off and unplugged before you clean it. Do not allow water to get inside the printer.

  caution:

Do not use abrasive cleaners on the printer.

Any maintenance or repairs beyond this should be done by a qualified service technician.

"Normal" printer use means less than

• 20 pages per day (if medium-density E/A0 CAD plots), or
• 12 pages per day (if medium-density E/A0 image prints).

  note:

  If your drawings are smaller than E/A0, the number of pages per day can be higher. If printer use is less than this amount, it is unlikely you will need to have it serviced. If printer use exceeds this amount, it is possible that, after a period of time, service will be necessary.

The printer itself keeps an internal count of total pages printed and total passes of the cartridge carriage. If the front panel periodically displays Status: Maintenance Advised, this means that your use of the printer has exceeded one of the following warranty limits:

• either 20,000 pages printed
• or 4,500,000 passes of the cartridge carriage.

Contact your local HP dealer or HP service engineer to arrange to have your printer serviced. After servicing, the message will disappear. If you choose not to have the printer serviced, you may continue to use the printer as normal, but may encounter a number of operational or print-quality problems.

You can check your current count of pages printed and passes of cartridge carriage by printing the Service Configuration Plot.

(1) Mean Time Between Failures (MTBF) = (usage hrs/yr)/(AFR) considering a usage of 15 plots per day

You can obtain current Material Safety Data Sheets for the print cartridge via the HP Web site (www.hp.com) HP Part number as follows:

The U.S. Federal Communications Commission (in 47 cfr 15.105) has specified that the following notice be brought to the attention of users of this product.

This equipment has received testing was found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, no guarantee exists that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference's by one or more of the following measures:

• Reorient the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

The user may find useful the following booklet prepared by the FCC: "How to Identify and Resolve Radio-TV Interference Problems". This booklet is available from the US Government Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4.

  caution:

Pursuant to Part 15.21 of the FCC Rules, any changes or modifications to this equipment not expressly approved by HP, may cause harmful interference and void the FCC authorization to operate this equipment.

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

The HP DesignJet 700 printers, models C4705A and C4706A are approved under Approval Number NS/G/1234/5/100003 for indirect connection to public telecommunication systems within the United Kingdom.