HP Z240 Tower Workstation Specifications

Product image

System board

Physical security and serviceability

BIOS

Manageability

Processors

Storage/hard drives

Graphics

Optical and removable storage

Controller cards

Networking and communications

Physical features

Product image

Figure : HP Z240 Tower Workstation

System board

Specification	Description
System board form factor	ATX 24.89 x 24.38 mm (9.8 x 9.6 in)
Processor socket	Single LGA 1151
CPU bus speed	DMI
Memory expansion slots	4 DDR4 memory slots
Memory type supported	DDR4, UDIMM (unbuffered), ECC and non-ECC
Memory modes	Non-interleaved for single channel. Interleaved when both channels are populated.
Memory speed supported	2133MT/s DDR4
Memory protection	ECC available on data
Maximum memory	64 GB
Memory configuration	4GB, 8GB and 16GB non-ECC/4GB, 8GB and 16GB ECC unbuffered DIMMs are supported. ECC and non-ECC memory DIMMs cannot be mixed on the same system.
PCI express connectors	1 PCI Express Gen3 slot x 1 mechanical/ x 1 electrical (full height, full length) 1 PCI Express Gen3 slot x 16 mechanical/ x 16 electrical (full height, full length) 1 PCI Express Gen3 slot x 4 mechanical/ x 4 electrical (full height, full length) 1 PCI Express Gen3 slot x 16 mechanical/ x 4 electrical (full height, full length) note: In the PCIe Gen3 (x 16 electrical/x 16 mechanical) slot, if it is not being used for a graphics card, only cards certified as After Market Options for this platform are supported.
PCI connectors (5 V)	1 (optional) PCI slot, full height, full length
Supported drive interfaces	SATA: Integrated (4) Serial ATA interfaces (6 Gb/s SATA). One port can optionally be used for eSATA. RAID 0 and 1 supported. Factory integrated RAID is Microsoft Windows only. RAID 5 is supported by Software XOR. Serial Attached SCSI None Integrated RAID: note: Requires identical hard drives (speeds, capacity, interface) Integrated graphics: Intel HD Graphics 530 (on Core i3/i5/i7-6xxx processors); Intel Integrated Graphics for Xeon processors Based on Unified Memory Architecture (UMA) - a region of system memory is reserved and dedicated to the graphics display. Support for Mic1 DVI-D and 2 DP 1.2 graphics ports integrated in motherboard; Supports up to three simultaneous displays across DP and DVI-D outputs. 1 DVI-D and 2 DP 1.2 graphics ports integrated in motherboard; Supports up to three simultaneous displays across DP and DVI-D outputs. Maximum resolution supported on DVI- D ports: 1920 x 1200 at 60Hz Maximum resolution supported on DP 1.2 ports: 3840x2160 at 60Hz Network controller: Integrated Ethernet PHY Connection I219LM. Management capabilities: WOL, PXE 2.1 and AMT 9 External SATA (eSATA): External SATA (eSATA): 1 port eSATA capable (SATA 3) with optional eSATA after-market option cable kit IDE connector: No Floppy connector: No Serial: 1 internal header (requires optional serial port adapter kit) 2nd Serial: No Parallel: 1 internal header (optional parallel port adapter required) HD integrated audio: Yes
USB connectors	Front: 2 USB 3.0, 1 USB 2.0, 1 USB 2.0 charging data port Rear: 4 USB 3.0, 2 USB 2.0 Internal: 1 USB 3.0 and 3 USB 2.0 ports available as 2 separate 2 x 6 (3.0 x 1.2.0 x 1) and 1 x 6 (2.0 x 1) headers: supports 1 HP Internal USB port kits plus one USB 3.0 SD card reader
HD integrated audio	Yes
Flash ROM	Yes
CPU fan header	Yes
Chassis fan header	1 rear system chassis fan header
Front control panel/speaker header	Yes
CMOS battery holder - lithium	Yes
Integrated trusted platform module	Integrated TPM 1.2 The TPM module disabled where restricted by law, i.e. Russia
Power supply headers	Yes
Power switch, power LED and hard drive LED header	Yes
Clear password jumper	Yes
Keyboard/mouse	USB or PS/2
Operating voltage range	90-269 VAC Maximum: 890 btu/hr (224 kcal/hr)
Rated voltage range	100-240 VAC
Rated line frequency	50-60 Hz
Operating line frequency range	47-66 Hz
Rated input current	6A at 100-240 V
Heat dissipation	Typical: 444 btu/hr (112 kcal/hr) Maximum: 1484 btu/hr (374 kcal/hr)
Power supply fan	80 x 80 x 25 mm (3.1 x 3.1 x 0.98 in) 4-wire PWM
ENERGY STAR qualified (config dependent)	Yes
CECP compliant at 220V	Yes
FEMP standby power compliant	Yes, with wake-on-LAN disabled: < 2 W in 55 - power off
Built-in self test (BIST) LED	Yes
Surge tolerant full ranging power supply (withstands power surges up to 2000 V)	Yes
Hood lock header	Yes
ErP Lot 6- Tier 1 compliance at 230 V	Yes
ErP Lot 6- Tier 2 compliance at 230 V	Yes
Environmental requirements	Temperature: Operating: 5° to 35° C (40° to 95° F) Non-operating: -40° to 60° C (-40° to 140° F) Humidity: Operating: 10% to 90% (non-condensing) Non-operating: 5% to 95%, 38.7° C (101.6° F) maximum wet bulb temperature Maximum altitude: Operating: 3,000 m (10,000 ft) Non-operating: 9,100 m (30,000 ft) Dynamic Operating: 40 g, 2-3 ms, half-sine Non-operating: 160 cm/s, 2-3 ms, half-sine. Square: 422 cm/s, 20 g Vibration: Operating random: 0.5g (rms), 5-300 Hz Non-operating random: 2.0g (rms), 10-500 Hz
Cooling	Above 1524 m (5,000 ft) altitude, maximum operating temperature is de-rated by 1.8° F (1° C) per 305 m (1000 ft) elevation increase.

Physical security and serviceability

Specification	Description
Access panel	Tool-less, except for the processor heatsink.
Optical drive	Tool-less
Hard drives	Tool-less
Expansion cards	Tool-less
Processor socket	Tool-less, except for the processor heatsink
Green user touch points	Yes, on tool-less internal chassis mechanisms
Color-coordinated cables and connectors	Yes
Memory	Tool-less
System board	Screw-in
Dual color power and HD LED on front of computer	Yes
Configuration record SW	Yes
Over-temp warning on screen	Yes
Restore CD/DVD set	Consists of an operating system DVD (OSDVD) and a driver DVD (DRDVD). OSDVD restores the original operating system. DRDVD will provide all drivers for the system. The DRDVD may also contain applications that originally shipped with the system for optional installation. Applications can also be obtained from HP.com. OSDVD and DRDVD are orderable with the system and available from HP Support.
Dual function front power switch	Yes, causes a fail-safe power off when held for 4 seconds
Padlock support	Yes (optional): locks side cover and secures chassis from theft 0.22 in diameter padlock loop at rear of system
Cable lock support	Yes, Kensington Cable Lock (optional): Locks side cover and secures chassis from theft 3 mm x 7 mm slot at rear of system
Universal chassis clamp lock support	Yes (optional): Locks side cover and locks cables to chassis. Secures chassis from theft and allows multiple units to be chained together when used with optional cable Threaded feature at rear of system
Solenoid lock and hood sensor	Yes (optional) The Solenoid Hood Lock eliminates the need for a physical key by making the chassis lockable through software and a password. You can also lock and unlock the chassis remotely over the network. The sensor kit detects when the access panel has been removed.
Rear port control cover	Yes, locks rear IO cables to prevent cable theft
Serial, parallel, USB, audio, network, enable/disable port control	Yes, enables or disables serial, USB, audio, and network ports
Removable media write/boot control	Yes, prevents ability to boot from removable media on supported devices (and can disable writes to media)
Power-on password	Yes, prevents an unauthorized person from booting up the workstation
Setup password	Yes, prevents an unauthorized person from changing the workstation configuration
3.3 V aux power LED on system PCA	Yes
NIC LEDs (integrated) (green and amber)	Yes
CPUs and heatsinks	A T-15 Torx or flat blade screwdriver is needed to remove the CPU heatsink before the CPU can be removed. CPU removal is tool-less
Power supply diagnostic LED	Yes
Front power button	Yes, ACPI multi-function
Front power LED	Yes
Front hard drive activity LED	Yes, white
Front ODD activity LED	Yes
Internal speaker	Yes
System/emergency ROM flash recovery	Recovers corrupted system BIOS.
Cooling solutions	92 x 92 x 25 mm 4-wire PWM (non-serviceable)
Power supply fans	92 x 92 x 25 mm 4-wire PWM (non-serviceable)
CPU heatsink fan	Mainstream (<= 65 W; 92 mm x 92 mm x 52.5 mm
Chassis fan	No
Memory heatsink fan	Advanced Configuration and Power Management Interface (ACPI). Allows the system to wake from a low power mode and controls system power consumption, making it possible to place individual cards and peripherals in a low-power or powered-off state without affecting other elements of the system
HP PC hardware diagnostics UEFI	HP PC Hardware Diagnostics (UEFI) enables hardware level testing outside the operating system on many components. The diagnostics can be invoked by pressing F2 at POST, and is available as a download from HP Support.
Access panel key lock	No
ACPI-ready hardware	Advanced Configuration and Power Management Interface (ACPI): Allows the system to wake from a low power mode. Controls system power consumption, making it possible to place individual cards and peripherals in a low-power or powered-off state without affecting other elements of the system.
Integrated chassis handles	Rear recessed handle; optional optical bay front handle available.
Power supply	Requires T15 Torx or flat blade screwdriver
PCI card retention	Yes, rear (all), middle (optional), front (full-length cards with extender)
Flash ROM	Yes
Diagnostic power switch LED on board	Yes
Clear password jumper	Yes
Clear CMOS button	Yes
DIMM connectors	Yes

BIOS

Specification	Description
BIOS 32-bit Services	Standard BIOS 32-bit Service Directory Proposal v 0.4
PCI 3.0 support	Full BIOS support for PCI Express through industry standard interfaces
ATAPI	ATAPI Removable Media Device BIOS Specification Version 1.0
BBS	BIOS Boot Specification v 1.01 Provides more control over how and from what devices the workstation will boot
WMI support	WMI is Microsoft's implementation of Web-Based Enterprise Management (WBEM) for Windows. WMI is fully compliant with the Distributed Management Task Force (DMTF) Common Information Model (CIM) and WBEM specifications
BIOS power on	Users can define a specific day-of-week and time for the system to power on
ROM based computer setup utility (F10)	Review and customize system configuration settings controlled by the BIOS
System/emergency ROM flash recovery with video	Recovers system BIOS in corrupted Flash ROM
Replicated setup	Saves BIOS settings to USB flash device in human readable file. Repsetup.exe utility can then replicate these settings on machines being deployed without entering Computer Configuration Utility (F10 Setup)
SMBIOS	System Management BIOS 2.7.1, for system management information
Boot control	Disables the ability to boot from removable media on supported devices
Memory change alert	Alerts management console if memory is removed or changed Makes it possible to place individual cards and peripherals in a low-power or powered-off state without affecting other elements of the system. Supports ACPI 4.0 for full compatibility with 64-bit operating systems.
Thermal alert	Monitors the temperature state within the chassis. Three modes: NORMAL - normal temperature ranges ALERTED - excessive temperatures are detected, raises a flag so action can be taken to avoid shutdown or provide for a smoother system shutdown. SHUTDOWN - excessive temperatures are encountered. Automatically shuts down the computer without warning before hardware component damage occurs.
Remote ROM flash	Provides secure, fail-safe ROM image management from a central network console. Updates can be performed before starting the OS Updates can be periodically scheduled
ACPI (Advanced Configuration and Power Management Interface)	Allows the system to enter and resume from low power modes (sleep states) Enables an operating system to control system power consumption based on the dynamic workload Makes it possible to place individual cards and peripherals in a low-power or powered-off state without affecting other elements of the system Supports ACPI 4.0 for full compatibility with 64-bit operating systems.
Ownership tag	A user-defined string stored in non-volatile memory that is displayed in the BIOS splash screen.
Remote wakeup/remote shutdown	System administrators can power on, restart, and power off a client computer from a remote location
ASF 2.0 compliant	No
Instantly available PC (suspend to RAM - ACPI sleep state S3)	Allows for very low power consumption with quick resume time
Remote system installation via F12 (PXE 2.1) (Remote Boot from Server)	Allows a new or existing system to boot over the network and download software, including the operating system
ROM revision levels	Reports the system BIOS revision level in Computer Configuration Utility (F10 Setup). Version is available through an industry standard interface (SMBIOS) so that management SW applications can use and report this information
System board revision level	Allows management SW to read revision level of the system board Revision level is digitally encoded into the HW and cannot be modified
Start-up diagnostics (power-on self-test)	Assesses system health at boot time with selectable levels of testing
Auto setup when new hardware installed	System automatically detects addition of new hardware.
Keyboard-less operation	The system can be booted without a keyboard
Localized ROM setup	Common BIOS image supports System Configuration Utility (F10 Setup) menus in 12 languages with local keyboard mappings
Asset tag	Enables the user or IT administrator to set a unique tag string in non-volatile memory
Per-slot control	Allows I/O slot parameters (option ROM enable/disable) to be configured individually
Adaptive cooling	Control parameters are set according to detected hardware configuration for optimal acoustics
Pre-boot diagnostics	(Pre-video) critical errors are reported via beeps and blinks on the power LED
Intel Active Management Technology (AMT)	AMT 11.0; allows workstation status to be monitored on a remote console
Digitally and cryptographically signed BIOS	Helps to prevent the installation of unauthorized versions of a BIOS (a rogue BIOS) from a virus, malware, or other code that could lead to compromised system security, data access, physical service, or even system board replacement
Master boot record protection	A feature in the HP BIOS that prevents changes and/or infections to the Master Boot Record. Useful in protecting from viruses
Boot block emergency recovery mode (BIOS Recovery)	The HP BIOS offers a write-protected boot block ROM that provides recovery from a failed flashing of the computer BIOS. This special recovery mode prevents the system from becoming unusable or "bricked" when a BIOS update is interrupted
Industry standard	Revision supported by the BIOS
UEFI specification revision	UEFI 2.4.0
ACPI	Advanced Configuration and Power Management Interface, Version 4.0
ASF	Alert Standard Format Specification, Version 2.0
ATA (IDE)	AT Attachment 6 with Packet Interface (ATA/ATAPI-6), Revision 3b
CD Boot	"El Torito" Bootable CD-ROM Format Specification Version 1.0
EDD	Enhanced Disk Drive Specification Version 1.1 BIOS Enhanced Disk Drive Specification Version 3.0
PCI	PCI Local Bus Specification, Revision 2.3 PCI Power Management Specification, Revision 1.1 PCI Firmware Specification, Revision 3.0
PCI express	PCI Express Base Specification, Revision 2.0 PCI Express Base Specification, Revision 3.0
PMM	POST Memory Manager Specification, Version 1.01
SATA	Serial ATA Specification, Revision 1.0a -Serial ATAII: Extensions to Serial ATA 1.0, Revision 1.0a Serial ATAII Cables and Connectors Volume 2 Gold SATA-IO SATA Revision 3.0 Specification
SPD	PC SDRAM Serial Presence Detect (SPD) Specification, Revision 1.2B
TPM	Trusted Computing Group TPM Specification Version 1.2
USB	Universal Serial Bus Revision 1.1 Specification Universal Serial Bus Revision 2.0 Specification Universal Serial Bus Revision 3.0 Specification

Manageability

Specification	Description
Intel Active Management Technology (AMT)	An advanced set of remote management features and functionality which provides network administrators the latest and most effective tools to remotely discover, heal, and protect networked client systems regardless of the system's health or power state. AMT 11.0 includes the following advanced management functions: Power management (on, off, standby, reset) Hardware/software inventory (includes BIOS and firmware revisions Hardware alerting Agent presence System defense filters SOL (Serial Over LAN) ME wake-on-LAN DASH 1.1 compliance IPv6 support Fast call for help - a client inside or outside the firewall may initiate a call for help via BIOS screen, periodic connections, or alert triggered connection Remote scheduled maintenance - pre-schedule when the PC connects to the IT or service provider console for maintenance. Remote PCs can get required patches, be inventoried, etc by connecting to their IT console or Service Provider when it's convenient Remote alerts - automatically alert IT or service provider if issues arise Access monitor - provides oversight into Intel AMT actions to support security requirements PC alarm clock Protected audio video path (PAVP) Microsoft NAP support Host base set-up and configuration Management Engine (ME) firmware roll back Enhanced KVM resolution (Up to 4K)
Intel vPro technology	The HP Z240 workstations support Intel vPro technology when purchased with a vPro technology capable CPU: Intel Xeon E3 processor family or 6th Generation Intel Core i5/i7 processors with Intel VT-d/VT-x and Intel TXT technology
Service, support, and warranty	Program to proactively communicate Product Change Notifications (PCNs) and customer advisories by email to customers, based on a user-defined profile. PCNs provide advance notification of hardware and software changes to be implemented in the factory providing time to plan for transition. Customer advisories provide concise, effective problem resolution, greatly reducing the need to call technical support

Processors

Specification	Description
6th generation Intel Core processor family	Intel Core i7-6700 3.4 2133 4C CPU Intel Core i7-6600 3.3 2133 4C CPU Intel Core i7-6500 3.2 2133 4C CPU

Storage/hard drives

SATA Hard Drives for HP workstations

500 GB SATA 7200 rpm 6 Gb/s 3.5-in HDD

Specification	Description
Capacity	500 GB
Height	2.54 cm (1 in)
Width	Media diameter: 8.9 cm (3.5 in) Physical size: 10.17 cm (4 in)
Interface	Serial ATA (6.0 Gb/s), NCQ enabled
Synchronous transfer rate (maximum)	Up to 600 MB/s
Buffer	16 MB
Seek time (typical reads, includes controller overhead, including settling)	Single track: 2 ms Average: 11 ms Full stroke: 21 ms
Rotational speed	7,200 rpm
Logical blocks	976,773,168
Operating temperature	5° to 55° C (41° to 131° F)

1 TB SATA 7200 rpm 6 Gb/s 3.5-in HDD

Specification	Description
Capacity	1 TB (1000 GB)
Height	2.54 cm (1 in)
Width	Media diameter: 8.9 cm (3.5 in) Physical size: 10.17 cm (4 in)
Interface	Serial ATA (6.0 Gb/s), NCQ enabled
Synchronous transfer rate (maximum)	Up to 600 MB/s
Buffer	64 MB
Seek time (typical reads, includes controller overhead, including settling)	Single track: 2 ms Average: 11 ms Full stroke: 21 ms
Rotational speed	7,200 rpm
Logical blocks	1,953,525,168
Operating temperature	5° to 55° C (41° to 131° F)

2 TB SATA 7200 rpm 6 Gb/s 3.5-in HDD

Specification	Description
Capacity	2 TB
Height	2.54 cm (1 in)
Width	Media diameter: 8.9 cm (3.5 in) Physical size: 10.17 cm (4 in)
Interface	Serial ATA (6.0 Gb/s), NCQ enabled
Synchronous transfer rate (maximum)	Up to 600 MB/s
Buffer	64 MB
Seek time (typical reads, includes controller overhead, including settling)	Single track: 1 ms Average: 11 ms Full stroke: 18 ms
Rotational speed	7,200 rpm
Logical blocks	3,907,029,168
Operating temperature	5° to 55° C (41° to 131° F)

3 TB SATA 7200 rpm 6 Gb/s 3.5-in HDD

Specification	Description
Capacity	3 TB
Height	2.54 cm (1 in)
Width	Media diameter: 8.9 cm (3.5 in) Physical size: 10.17 cm (4 in)
Interface	Serial ATA (6.0 Gb/s), NCQ enabled
Synchronous transfer rate (maximum)	Up to 6.0 MB/s
Buffer	64 MB
Seek time (typical reads, includes controller overhead, including settling)	Single track: 0.6 ms Average: 11 ms Full stroke: Not specified
Rotational speed	7,200 rpm
Operating temperature	5° to 60° C (41° to 140° F)

128 GB SATA 6 Gb/s SSD

Specification	Description
Capacity	128 GB
Height	0.7 cm (0.28 in)
Width	Physical size: 6.36 cm (2.5 in)
Interface	SATA 6 Gb/s
Synchronous transfer rate (maximum)	Up to 550 MB/s (sequential read)
Operating temperature	0° to 70° C (32° to 158° F)

4TB SATA 7200 rpm 6 Gb/s 3.5-in HDD

Specification	Description
Capacity	4 TB
Height	2.54 cm (1 in)
Width	Media diameter: 8.9 cm (3.5 in) Physical size: 10.17 cm (4 in)
Interface	Serial ATA (6.0 Gb/s), NCQ enabled
Synchronous transfer rate (maximum)	Up to 600 MB/s
Buffer	32 MB
Seek time (typical reads, includes controller overhead, including settling)	Single track: 0.7 ms Average: 8.5 ms Full stroke:15.7
Rotational speed	7,200 rpm
Operating temperature	5° to 60° C (41° to 140° F)

500 GB SATA 7.2 K SED SFF HDD

Specification	Description
Capacity	500 GB
Height	0.7 cm (0.275 cm)
Width	Media diameter: 6.36 cm (2.5 in) Physical size: 6.99 cm (2.75 in)
Interface	Up to 600MB/s
Synchronous transfer rate (maximum)	128 MB
Buffer	64 MB
Seek time (typical reads, includes controller overhead, including settling)	Single track: 1 ms Average: 4.3 ms Full stroke: 25 ms (typical)
Rotational speed	7,200 rpm
Operating temperature	0° to 60° C (32° to 140° F)

1 TB SATA 7200 rpm 6 Gb/s 3.5-in HDD (hybrid)

Specification	Description
Capacity	1 TB (1000 GB)
Height	2.54 cm (1 in)
Width	Media diameter: 8.9 cm (3.5 in) Physical size: 10.17 cm (4 in)
Interface	Serial ATA (6.0 Gb/s)
Synchronous transfer rate (maximum)	Up to 600 MB/s
Buffer	64 MB
Cache	8 GB NAND flash
Rotational speed	7,200 rpm
Operating temperature	0° to 60° C (32° to 140° F)

HP Solid State Drives (SSDs) for workstations

HP 256 GB SATA 6Gb/s SSD

Specification	Description
Capacity	256 GB
Height	0.7 cm (0.28 in)
Interface	SATA 6Gb/s
Synchronous transfer rate (maximum)	Up to 500 MB/s
Operating temperature	0° to 70° C (32° to 158° F)

HP 256 GB SATA 6Gb/s SED Opal 2 SSD

Specification	Description
Capacity	256 GB
Height	0.7 cm (0.28 in)
Interface	SATA 6Gb/s
Synchronous transfer rate (maximum)	Up to 550 MB/s
Operating temperature	0° to 70° C (32° to 158° F)

HP 512 GB SATA 6Gb/s SSD

Specification	Description
Capacity	512 GB
Height	0.7 cm (0.28 in)
Width	6.36 cm (2.5 in)
Interface	SATA 6Gb/s
Synchronous transfer rate (maximum)	Up to 550 MB/s
Operating temperature	0° to 70° C (32° to 158° F)

HP 1 TB SATA 6Gb/s SSD

Specification	Description
Capacity	1 TB
Height	0.7 cm (0.28 in)
Width	6.36 cm (2.5 in)
Interface	SATA 6Gb/s
Synchronous transfer rate (maximum)	Up to 500 MB/s
Operating temperature	0° to 70° C (32° to 158° F)

PCIe SSDs for HP workstations

HP Z turbo drive G2 128 GB SSD

Specification	Description
Capacity	128 GB
Interface	PCI Express 2 x 4 electrical x 4 physical
Operating temperature	0° to 70° C (32° to 158° F)

Specification	Description
Capacity	256 GB
Interface	PCI Express 2 x 4 electrical x 4 physical
Operating temperature	0° to 70° C (32° to 158° F)

HP Z turbo drive G2 512 GB SSD

Specification	Description
Capacity	512 GB
Interface	PCI Express 2 x 4 electrical x 4 physical
Operating temperature	0° to 70° C (32° to 158° F)

Graphics

Integrated Intel HD graphics

Specification	Description
Form factor	Integrated in select Intel Xeon E3, Intel Core i7, and Intel Core i5 processors.
Graphics controller	Intel HD graphics
Memory	Unified Memory Architecture (UMA) frame buffer. Graphics memory is shared with system memory. Size selectable between 64 MB to 512 MB via BIOS setting. Default size is 64 MB. Additional memory is allocated for graphics as needed using Intel's Dynamic Video Memory Technology (Intel DVMT 5.0), to provide an optimal balance between graphics and system memory use.
Connectors	Check system platform specifications where Intel HD Graphics are available
Maximum resolution	Display Port: 2560 x 1600 DVI: 192 0x 1200 VGA: 2048 x 1536 note: For DVI and VGA outputs, separate adapters may be required.
Shading architecture	Shader model 5
Supported graphics APIs	OpenGL 4 DirectX 11.1
Available graphics drivers	Windows 10 Windows 7

NVIDIA NVS 310 512 MB graphics

Specification	Description
Form factor	Low Profile: 2.71 × 6.15 in
Graphics controller	NVIDIA NVS 310
Bus type	PCI express x 16, 2 compliant
Memory	Size: 512 GB DDR3 Clock: 875 Mhz Memory bandwidth: 14 GB/s
Connectors	2 x DisplayPort 1.2
Maximum resolution	Up to 2560 x 1600 (digital display) per display.
Image quality features	The following video formats are supported: MPEG2 MPEG4 Part 2 Advanced Simple Profile H.264 SVC codec support Support for 3D Blu-Ray VC1 DivX version 3.11 or later MVC A full range of video resolutions are supported including 1080p, 1080i, 720p, 480p and 480i. The NVS 315 GPU provides hardware acceleration for the computationally intensive parts of video processing, as well as provides improved video playback speeds via faster decode and transcode.
Display output	Up to 2 displays using one of the following DMS-59 cables: DisplayPort output: Drives two DisplayPort enabled digital display at resolutions up to 2560 × 1600 at 60 Hz with reduced blanking, when connected natively using the 2 DisplayPort connectors on the NVS 310 graphics card Supports 2 monitors up to resolution of 1920 × 1200 at 60 Hz with reduced blanking using DisplayPort 1.2 multi stream topology technology. DVI-D output: Drives two digital display at resolutions up to 1920 × 1200 at 60 Hz with reduced blanking using DisplayPort to DVI-D single-link cable adaptors Drives two digital display at resolutions up to 2560× 1600 at 60 Hz with reduced blanking using DisplayPort to DVI-D dual-link cable adaptors HDMI output: NVS 310 is capable of driving two high definition (HD) panels up to resolutions of 1920 × 1080P at 60 Hz using DisplayPort to HDMI cable adaptors VGA display output: Drives two analog display at resolutions up to 2048 × 1536 at 85 Hz using DMS-59 to VGA cable adaptors
Shading architecture	Shader model 5.0
Supported graphics APIs	OpenGL 4.3 DirectX 11.1
Available graphics drivers	Windows 7 Professional (64-bit and 32-bit) Windows XP Professional (64-bit and 32-bit) Red Hat Enterprise Linux (RHEL) SUSE Linux Enterprise Desktop 11 (64-bit and 32-bit)
Power consumption	19.5 W

NVIDIA NVS 315 512 MB graphics

Specification	Description
Form factor	Low Profile: 2.71 × 6.15 in Number of cores: 48 CUDA cores Weight: 142 g
Graphics controller	NVIDIA NVS 310 (using GF119-825 GPU) GPU: GF119-825
Bus type	PCI express x 16, 2.0 compliant
Memory	Size: 512 MB DDR3 Clock: 875 Mhz Memory bandwidth: 14 GB/s
Connectors	2 x DisplayPort
Maximum resolution	Up to 2560 x 1600 (digital display) per display.
Image quality features	The following video formats are supported: MPEG2 MPEG4 Part 2 Advanced Simple Profile H.264 SVC codec support Support for 3D Blu-Ray VC1 DivX version 3.11 or later MVC A full range of video resolutions are supported including 1080p, 1080i, 720p, 480p and 480i. The NVS 315 GPU provides hardware acceleration for the computationally intensive parts of video processing, as well as provides improved video playback speeds via faster decode and transcode.
Display output	Up to 2 displays in the following configurations: DisplayPort output: Drives two DisplayPort enabled digital display at resolutions up to 2560 × 1600 at 60 Hz with reduced blanking, when connected natively using the 2 DisplayPort connectors on the NVS 310 graphics card Supports 2 monitors up to resolution of 1920 × 1200 at 60 Hz with reduced blanking using DisplayPort 1.2 multi stream topology technology. DVI-D output: Drives two digital display at resolutions up to 1920 × 1200 at 60 Hz with reduced blanking using DisplayPort to DVI-D single-link cable adaptors Drives two digital display at resolutions up to 2560× 1600 at 60 Hz with reduced blanking using DisplayPort to DVI-D dual-link cable adaptors HDMI output: NVS 310 is capable of driving two high definition (HD) panels up to resolutions of 1920 × 1080P at 60 Hz using DisplayPort to HDMI cable adaptors VGA display output: Drives two analog display at resolutions up to 2048 × 1536 at 85 Hz using DMS-59 to VGA cable adaptors
Shading architecture	Shader model 5.0
Supported graphics APIs	OpenGL 5.0 DirectX 11.1, OpenGL 4.1
Available graphics drivers	Windows 7 Professional (64-bit and 32-bit) Windows XP Professional (64-bit and 32-bit) Red Hat Enterprise Linux (RHEL) SUSE Linux Enterprise Desktop 11 (64-bit and 32-bit)
Power consumption	19.5 W

NVIDIA NVS 315 1 GB graphics

Specification	Description
Form factor	Low Profile: 2.71 × 6.15 in Number of cores: 48 CUDA cores Weight: 142 grams
Graphics controller	NVIDIA NVS 310 (using GF119-825 GPU) GPU: GF119-825 Maximum power: 19.3 W Cooling solution: active fan heatsink
Bus type	PCI express x 16, 2.0 compliant
Memory	Size: 1 G DDR3 Clock: 875 Mhz Memory bandwidth: 14 GB/s
Connectors	DMS-59 output Cables included: For CTO: DMS-59 to DVI cable For AMO: DMS-59 to DVI cable and DMS-59 to VGA cable
Maximum resolution	Maximum number of displays supported: 2 Maximum resolution support: DMS-59 to VGA: 2048 x 1536 at 85Hz DMS-59 to DVI: 1980 x 1200 at 60Hz DMS-59 to DP: 2560 x 1600 at 60Hz
Image quality features	The following video formats are supported: MPEG2 MPEG4 Part 2 Advanced Simple Profile H.264 SVC codec support Support for 3D Blu-Ray VC1 DivX version 3.11 or later MVC A full range of video resolutions are supported including 1080p, 1080i, 720p, 480p and 480i. The NVS 315 GPU provides hardware acceleration for the computationally intensive parts of video processing, as well as provides improved video playback speeds via faster decode and transcode.
Display output	Up to 2 displays in the following configurations: DisplayPort output: Drives two DisplayPort enabled digital display at resolutions up to 2560 × 1600 at 60 Hz with reduced blanking, when connected natively using the 2 DisplayPort connectors on the NVS 310 graphics card DVI-D output: Drives two digital display at resolutions up to 1920 × 1200 at 60 Hz with reduced blanking using DisplayPort to DVI-D single-link cable adaptors VGA display output: Drives two analog display at resolutions up to 2048 × 1536 at 85 Hz using DMS-59 to VGA cable adaptors
Shading architecture	Shader model 5.0
Supported graphics APIs	OpenGL 5.0 DirectX 11.1, OpenGL 4.3
Available graphics drivers	Windows 8 Windows 7 Professional (64-bit and 32-bit) Windows XP Professional (64-bit and 32-bit) Red Hat Enterprise Linux (RHEL) SUSE Linux Enterprise Desktop 11 (64-bit and 32-bit)
Power consumption	19.5 W

NVIDIA NVS 510 2 GB graphics

Specification	Description
Form factor	Dimensions: 2.71 x 6.3 in, single slot
Graphics controller	NVS 510 GPU Core Clock: 797 Mhz Memory Clock: 891 Mhz CUDA Cores: 192
Bus type	PCI express x 16, generation 2.0
Memory	Size: 2 GB DDR3 Memory bandwidth: 29 GB/s Memory width: 128 bit
Connectors	Four mini-DisplayPort. Four mini-DisplayPort to DisplayPort adapters included. (DisplayPort to DVI-D, DisplayPort to VGA, DisplayPort to HDMI, and DisplayPort to Dual-Link DVI adapters available as separate accessories)
Maximum resolution	Mini-DisplayPort connectors support ultra-high-resolution panels (up to 3840 x 2160 at 60Hz) note: This card supports up to four displays. For Windows XP, only 2 active displays are supported.
Image quality features	10-bit internal display processing, including hardware support for 10-bit scan-out
Display output	DisplayPort with Multi-Stream Technology (MST) and High Bit Rate 2 (HBR2) support DisplayPort output: Drives two DisplayPort enabled digital display at resolutions up to 2560 × 1600 at 60 Hz with reduced blanking, when connected natively using the 2 DisplayPort connectors on the NVS 310 graphics card Supports 2 monitors up to resolution of 1920 × 1200 at 60 Hz with reduced blanking using DisplayPort 1.2 multi stream topology technology DVI-D output: Drives two digital display at resolutions up to 1920 × 1200 at 60 Hz with reduced blanking using DisplayPort to DVI-D single-link cable adaptors Drives two digital display at resolutions up to 2560× 1600 at 60 Hz with reduced blanking using DisplayPort to DVI-D dual-link cable adaptors HDMI output: NVS 310 is capable of driving two high definition (HD) panels up to resolutions of 1920 × 1080P at 60 Hz using DisplayPort to HDMI cable adaptors VGA display output: Drives two analog display at resolutions up to 2048 × 1536 at 85 Hz using DMS-59 to VGA cable adaptors DisplayPort output: Drives four DisplayPort enabled digital display at resolutions up to 3840 × 2160 at 60 Hz with reduced blanking, when connected natively using the 4 DisplayPort connectors on the NVS 510 graphics card. DisplayPort Multi-Stream Topology (MST) Technology: Supports various combinations of display resolutions and number of displays when using DisplayPort multi stream topology technology - up to a maximum of 4 monitors at a resolution of 1920 × 1200 at 60 Hz with reduced blanking. DVI-D output: Drivesfour digital display at resolutions up to 1920 × 1200 at 60 Hz with reduced blanking using DisplayPort to DVI-D single-link cable adaptors Drives four digital display at resolutions up to 2560× 1600 at 60 Hz with reduced blanking using DisplayPort to DVI-D dual-link cable adaptors HDMI output: NVS 510 graphics board is capable of driving four high definition (HD) panels up to resolutions of 1920 × 1080P at 60 Hz using DisplayPort to HDMI cable adaptors VGA display output: Drives four analog displays at resolutions up to 1920 × 1200 at 60 Hz using DisplayPort to VGA cable adaptors
Supported graphics APIs	Full Microsoft DirectX 11, Shader Model 5.0 support Full OpenGL 4.3 support
Available graphics drivers	Windows 7 Professional (64-bit and 32-bit) Windows XP Professional (64-bit and 32-bit) Red Hat Enterprise Linux (RHEL) SUSE Linux Enterprise Desktop 11 (64-bit and 32-bit)
Power consumption	33.4 W

AMD FirePro W2100 2 GB

Specification	Description
Form factor	Low Profile, half length (full-height bracket included)
Graphics controller	AMD FirePro W2100 professional graphics based on Oland GPU GPU: 320 stream processors organized into 5 Compute Units GPU frequency: 630 Mhz Power: 26 W Cooling: Active
Bus type	PCI express x8, Generation 3.0
Memory	2 GB DDR3 memory Memory bandwidth: up to 28.8 GB/s Memory wdth: 128 bit
Connectors	2 x Display Port 1.2 connectors Factory configured: No video cable adapter included After market option kit: No video cable adapter included Additional DisplayPort-to-VGA or DisplayPort-to-DVI adapters are available as Factory Configuration or Option Kit accessories.
Maximum resolution	DisplayPort 1.2: up to 4096 x 2160 x 24 bpp at 60 Hz Dual link DVI(I) (requires adapter cable): up to 2560 x 1600 x 32 bpp at 60 Hz Single link-DVI (I) (requires adapter cable): up to 1920 x 1200 x 32 bpp at 60 Hz VGA (requires adapter cable): up to 1920 x 1200 x 32 bpp at 60 Hz
Image quality features	Advanced support for 8-bit, 10-bit, and 16-bit per RGB color component. High bandwidth scaler for high quality up and downscaling.
Display output	2 x DisplayPort 1.2a Maximum number of displays: 2
Shading architecture	Shader model 5.0
Supported graphics APIs	OpenCL 1.2 DirectX 11.2/12 OpenGL 4.4 OpenGL 4.4 support with driver release 14.301.xxx OpenCL 1.2 conformance expected with drive release 14.301.xxx
Available graphics drivers	Windows 8.1 (64-bit and 32-bit) Windows 7 (64-bit and 32-bit) Linux

NVIDIA Quadro K420 1 GB Graphics

Specification	Description
Form factor	Low Profile, single slot Dimensions: 2.71 × 6.3 in Cooling: Active
Graphics controller	NVIDIA Quadro K420 GPU: GK107 with 192 CUDA cores Power: 41 W
Bus type	PCI express x16, 2.0 compliant
Memory	Size: 1 GB DDR3 Clock: 891 MHz Memory bandwidth: 29 GB/s Memory width: 128 bit
Connectors	One dual-link DVI-I connector One DisplayPort connector Factory configured: No video cable adapter included After market option kit: One DP-to-DVI adapter included with card Additional DisplayPort-to-VGA or DisplayPort-to-DVI adapters are available as Factory Configuration or Option Kit accessories
Maximum resolution	VGA (via adapter cable): 2048 × 1536 × 32 bpp at 85 Hz Dual-link DVI: 2560 × 1600 × 32 bpp at 60 Hz (reduced blanking) Single-link DVI: 1920 × 1200 × 32 bpp at 60 Hz (reduced blanking) DisplayPort 1.2: 3840 × 2160 × 30 bpp at 60 Hz
Image quality features	12-bit internal display pipeline (hardware support for 12-bit scanout on supported panels, applications and connection) Stereoscopic 3D display support including NVIDIA 3D Vision technology, 3D DLP, Interleaved, and passive stereo
Display output	Maximum number of displays 2 direct attached monitors 4 using DP 1.2a with MST and HBR2 enabled monitors Maximum number of DisplayPort displays possible (may require MST and/or HBR2) 1920 x 1200 - 4 2560 x 1600 - 2 3840 x 2160 - 1 Maximum number of monitors across all available Quadro K420 outputs is 4
Shading architecture	Shader model 5.0
Supported graphics APIs	DX11 OpenGL 4.4 Programming support for CUDA C CUDA C++ DirectCompute 5.0 OpenCL Python Fortran
Available graphics drivers	Microsoft Windows 8.1 Microsoft Windows 8 Microsoft Windows 7 Linux (Full OpenGL implementation, complete with NVIDIA and ARB extensions)

NVIDIA Quadro K620 2 GB Graphics

Specification	Description
Form factor	Dimensions: 2.71 x 6.3 in Single slot, low profile Cooling: active Weight: 133 grams
Graphics controller	NVIDIA Quadro K620 GPU: GM 107 GPU with 384 CUDA cores Power: 45 W
Bus type	PCI express 20 x16
Memory	Size: 2 GB DDR3 Memory bandwidth: 29 GB/s Memory width: 128 bit
Connectors	One dual-link DVI-I connector One DisplayPort connector Factory configured: No video cable adapter included After market option kit: One DP-to-DVI adapter included with card Additional DVI-to-VGA, DisplayPort-to-VGA, or DisplayPort-to-DVI adapters are available as Factory Configuration or Option Kit accessories
Maximum resolution	DisplayPort 1.2: up to 4096 x 2160 x 30 bpp at 60 Hz, supports High Bit Rate 2 (HBR2) and Multi-Stream Transport (MST) Dual Link DVI(I) output: up to 2560 x 1600 x 32 bpp at 60 Hz Single Link-DVI(I) output: up to 1920 x 1200 x 32 bpp at 60 Hz VGA (via adapter cable): 2048 × 1536 × 32 bpp at 85 Hz
Image quality features	12-bit internal display pipeline (hardware support for 12-bit scanout on supported panels, applications and connection) Stereoscopic 3D display support including NVIDIA 3D Vision technology, 3D DLP, Interleaved, and passive stereo
Display output	Maximum number of displays 2 direct attached monitors 4 using DP 1.2a with MST and HBR2 enabled monitors Maximum number of DisplayPort displays possible (may require MST and/or HBR2) 1920 x 1200 - 4 2560 x 1600 - 2 3840 x 2160 - 1 Maximum number of monitors across all available Quadro K620 outputs is 4
Shading architecture	Shader model 5.0
Supported graphics APIs	OpenGL 4.4 DirectX 11 API support includes: CUDA C, CUDA C++, DirectCompute 5.0, OpenCL, Java, Python, and Fortran
Available graphics drivers	Microsoft Windows 8.1 Microsoft Windows 8 Microsoft Windows 7 Linux (Full OpenGL implementation, complete with NVIDIA and ARB extensions)

AMD FirePro W5100 4 GB

Specification	Description
Form factor	Dimensions: 2.71 x 6.3 in Single slot, low profile Cooling: active Weight: 133 grams
Graphics controller	NVIDIA Quadro K620 GPU: GM 107 GPU with 384 CUDA cores Power: 45 W
Bus type	PCI express 20 x16
Memory	Size: 2 GB DDR3 Memory bandwidth: 29 GB/s Memory width: 128 bit
Connectors	One dual-link DVI-I connector One DisplayPort connector Factory configured: No video cable adapter included After market option kit: One DP-to-DVI adapter included with card Additional DVI-to-VGA, DisplayPort-to-VGA, or DisplayPort-to-DVI adapters are available as Factory Configuration or Option Kit accessories
Maximum resolution	DisplayPort 1.2: up to 4096 x 2160 x 30 bpp at 60 Hz, supports High Bit Rate 2 (HBR2) and Multi-Stream Transport (MST) Dual link DVI(I) output: up to 2560 x 1600 x 32 bpp at 60 Hz Single link-DVI(I) output: up to 1920 x 1200 x 32 bpp at 60 Hz VGA (via adapter cable): 2048 × 1536 × 32 bpp at 85 Hz
Image quality features	12-bit internal display pipeline (hardware support for 12-bit scanout on supported panels, applications and connection) Stereoscopic 3D display support including NVIDIA 3D Vision technology, 3D DLP, Interleaved, and passive stereo
Display output	Maximum number of displays 2 direct attached monitors 4 using DP 1.2a with MST and HBR2 enabled monitors Maximum number of DisplayPort displays possible (may require MST and/or HBR2) 1920 x 1200 - 4 2560 x 1600 - 2 3840 x 2160 - 1 Maximum number of monitors across all available Quadro K620 outputs is 4
Shading architecture	Shader model 5.0
Supported graphics APIs	OpenGL 4.4 DirectX 11 API support includes: CUDA C, CUDA C++, DirectCompute 5.0, OpenCL, Java, Python, and Fortran
Available graphics drivers	Microsoft Windows 8.1 Microsoft Windows 8 Microsoft Windows 7 Linux (Full OpenGL implementation, complete with NVIDIA and ARB extensions)

NVIDIA Quadro K620 4 GB Graphics

Specification	Description
Form factor	Dimensions: 4.38 x 7.97 in Single slot, low profile Cooling: active Weight: 240 grams
Graphics controller	NVIDIA Quadro K2200 graphics card GPU: GM 107 GPU with 640 CUDA cores Power: 68 W
Bus type	PCI express 2 x16
Memory	Size:4 GB DDR3 Memory bandwidth: 80 GB/s Memory width: 128 bit
Connectors	One dual-link DVI-I connector One DisplayPort connector Factory configured: No video cable adapter included After market option kit: One DP-to-DVI adapter included with card Additional DVI-to-VGA, DisplayPort-to-VGA, or DisplayPort-to-DVI adapters are available as Factory Configuration or Option Kit accessories
Maximum resolution	Up to 4096 x 2160 x 30 bpp at 60 Hz, supports High Bit Rate 2 (HBR2) and Multi-Stream Transport (MST) Dual link DVI(I) output: up to 2560 x 1600 x 32 bpp at 60 Hz Single link-DVI(I) output: up to 1920 x 1200 x 32 bpp at 60 Hz VGA (via adapter cable): 2048 × 1536 × 32 bpp at 85 Hz
Image quality features	12-bit internal display pipeline (hardware support for 12-bit scanout on supported panels, applications and connection) Stereoscopic 3D display support including NVIDIA 3D Vision technology, 3D DLP, Interleaved, and passive stereo
Display output	Maximum number of displays 3 direct attached monitors 4 using DP 1.2a with MST and HBR2 enabled monitors Maximum number of DisplayPort displays possible (may require MST and/or HBR2) 1920 x 1200 - 4 2560 x 1600 -4 3840 x 2160 - 2 Maximum number of monitors across all available Quadro K2200outputs is 4
Shading architecture	Shader model 5.0
Supported graphics APIs	OpenGL 4.4 DirectX 11 API support includes: CUDA C, CUDA C++, DirectCompute 5.0, OpenCL, Java, Python, and Fortran
Available graphics drivers	Microsoft Windows 8.1 Microsoft Windows 8 Microsoft Windows 7 Linux (Full OpenGL implementation, complete with NVIDIA and ARB extensions)

AMD FirePro W7100 8 GB graphics

Specification	Description
Form factor	Full height, single slot 9.5 X 4.38 in
Graphics controller	AMD FirePro W7100 graphics GPU: 1792 stream processors organized into 28 compute units Power: < 75 W Cooling: active
Bus type	PCI Express x 16, Generation 3.0
Memory	8 GB GDDR5 memory Memory bandwidth: up to175 GB/s Memory width: 256 bit
Connectors	4 x DisplayPort 1.2a connectors with HBR2 and MST support. Factory Configured: No video cable adapter included. After market option kit: No video cable adapter included. Additional DisplayPort-to-VGA or DisplayPort-to-DVI adapters are available as Factory Configuration or Option Kit accessories.
Maximum resolution	Up to 4096 x 2160 x 30 bpp at 60 Hz, supports High Bit Rate 2 (HBR2) and Multi-Stream Transport (MST) Dual Link DVI(I) output: up to 2560 x 1600 (requires DP to DL-DVI adapter) Single Link-DVI(I) output: up to 1920 x 1200 (requires DP to DVI adapter) VGA (via adapter cable): 1920 x 1200 (requires DP to VGA adapter)
Image quality features	Advanced support for 8-bit, 10-bit, and 16-bit per RGB color component. High bandwidth scaler for high quality up and downscaling
Display output	Maximum number of displays 4 direct attached monitors 6 using DP 1.2a with MST and HBR2 enabled monitors Maximum number of DisplayPort displays possible (may require MST and/or HBR2) 4096 x 2160 - 1 2560 x 1600 -2 1920 x 1200 - 4
Shading architecture	Shader model 5.0
Supported graphics APIs	OpenGL 4.4 OpenCL 1.2 and 2.0 DirectX 11.2/12 AMD Mantle
Available graphics drivers	Microsoft Windows 8.1 Microsoft Windows 8 Microsoft Windows 7 Linux (Full OpenGL implementation, complete with NVIDIA and ARB extensions)

NVIDIA Quadro K4000 8 GB Graphics

Specification	Description
Form factor	Dimensions: 4.38 x 9.5 in Single slot, low profile Cooling: active Weight: 461 grams
Graphics controller	NVIDIA Quadro M4000 GPU: GK104-850 GPU with 1344 CUDA cores Power: 108 W
Bus type	PCI express 2 x16
Memory	Size:8 GB DDR3 Memory bandwidth: 173 GB/s Memory width: 256 bit
Connectors	1 - dual-link DVI-I connector 2 - DisplayPort 1.2a Factory configured: No video cable adapter included After market option kit: One DP-to-DVI adapter included with card Additional DVI-to-VGA, DisplayPort-to-VGA, or DisplayPort-to-DVI adapters are available as Factory Configuration or Option Kit accessories
Maximum resolution	Up to 3840 x 2160 x 30 bpp at 60 Hz, supports High Bit Rate 2 (HBR2) and Multi-Stream Transport (MST) Dual Link DVI(I) output: up to 2560 x 1600 x 32 bpp at 60 Hz Single Link-DVI(I) output: up to 1920 x 1200 x 32 bpp at 60 Hz VGA (via adapter cable): 2048 × 1536 × 32 bpp at 85 Hz
Image quality features	10-bit internal display processing (hardware support for 12-bit scanout on supported panels, applications and connection) NVIDIA 3D Vision technology, 3D DLP, Interleaved, and other 3D stereo format support Full OpenGL quad buffered stereo support Support for large-scale, ultra-high resolution visualization using the NVIDIA SVS platform which includes NVIDIA Mosaic, NVIDIA Sync and NVIDIA Warp/Blend technologies
Display output	Maximum number of displays 3 direct attached monitors 4 using DP 1.2a with MST and HBR2 enabled monitors Maximum number of DisplayPort displays possible (may require MST and/or HBR2) 1920 x 1200 - 4 2560 x 1600 -4 3840 x 2160 - 2 Maximum number of monitors across all available Quadro K2200 outputs is 4
Shading architecture	Shader model 5.0
Supported graphics APIs	OpenGL 4.4 DirectX 11 API support includes: CUDA C, CUDA C++, DirectCompute 5.0, OpenCL, Java, Python, and Fortran
Available graphics drivers	Microsoft Windows 8.1 Microsoft Windows 8 Microsoft Windows 7 Windows 10 Linux (Full OpenGL implementation, complete with NVIDIA and ARB extensions)

Optical and removable storage

HP Slim DVD-ROM Drive

Specification	Description
Drive	12.7 mm high, tray-load
Mounting orientation	Either horizontal or vertical
Interface type	SATA / ATAPI
Dimensions (W x H x D)	128 x 14 x 128 mm
Disc capacity	Single layer: up to 4.7 GB Double layer: up to 8.5 GB
Access times	DVD-ROM single layer: <110 ms (typical) CD-ROM mode 1: <110 ms (typical) Full stroke DVD: <230 ms (seek) Full stroke CD: <220 ms (seek)
Power	Source: SATA DC power receptacle DC power requirements: 5 VDC ± 5%-100 mV ripple p-p DC current: 5 VDC - <800 mA typical, <1600 mA maximum
Operating environmental (all conditions non-condensing)	Temperature: 5° to 50° C (41° to 122° F) Relative humidity: 10% to 80% Maximum wet bulb temperature: 29° C (84° F)
Operating systems supported	Windows 8 32-bit and 64-bit Windows 7 Professional 32-bit and 64-bit Windows Vista Business 64 Windows Vista Business 32 Windows Vista Home Basic 32 Windows 2000 Windows XP Professional or Windows XP Home 32 Red Hat Enterprise Linux(RHEL) WS4**, 5, 6 Desktop/Workstation

HP Slim SuperMulti DVDRW SATA drive

Specification	Description
Drive	12.7 mm high, tray-load
Mounting orientation	Either horizontal or vertical
Interface type	SATA / ATAPI
Dimensions (W x H x D)	128 x 14 x 128 mm
Disc formats	DVD-RAM DVD+R DVD+RW DVD+R DL DVD-R DL DVD-R DVD-RW CD-R CD-RW
Disc capacity	DVD-ROM single layer: 8.5 GB DL or 4.7 GB standard Full Stroke DVD: < 230 ms (seek) Full Stroke CD: < 200 ms (seek) Blu-ray: 50 GB DL or 25 GB standard
Maximum data transfer rates	CD-ROM read CD-ROM, CD-R Up to 24X CD-RW Up to 24X DVD-ROM read DVD-RAM up to 8 X DVD+RW up to 8 X DVD-RW up to 8 X DVD+R DL up to 8 X DVD-R DL up to 8 X DVD-ROM up to 8 X DVD-ROM DL up to 8 X DVD+R up to 8 X DVD-R up to 8 X
Power	Source: SATA DC power receptacle DC power requirements: 5 VDC ± 5%-100 mV ripple p-p DC current: 5 VDC - <800 mA typical, <1600 mA maximum
Operating environmental (all conditions non-condensing)	Temperature: 5° to 50° C (41° to 122° F) Relative humidity: 10% to 80% Maximum wet bulb temperature: 29° C (84° F)
Operating systems supported	Windows 8 32-bit and 64-bit Windows 7 Professional 32-bit and 64-bit Windows Vista Business 64 Windows Vista Business 32 Windows Vista Home Basic 32 Windows 2000 Windows XP Professional or Windows XP Home 32 Red Hat Enterprise Linux(RHEL) WS4**, 5, 6 Desktop/Workstation
Kit contents	HP SATA SuperMulti DVD Writer drive, Cyberlink Power2Go Software, Cyberlink PowerDVD Software, installation guide, and DVD+R media.

HP slim Blu-ray writer

Specification	Description
Mounting orientation	Horizontal
Interface type	SATA
Dimensions (W x H x D)	128 x 14 x 128 mm
Disc formats	BD-ROM BD-R BD-RE DVD-RAM DVD+R DVD+RW DVD+R DL DVD-R DL DVD-R DVD-RW CD-R CD-RW
Disc capacity	DVD-ROM single layer: 8.5 GB DL or 4.7 GB standard CD-ROM: 650 MB CD-ROM (Read Only) 800/700/650 MB CD-recordable (read & write) 700/650 MB high speed CD-rewritable (read & write) 700/650 MB ultra and ultra + speed CD-rewritable (read & write Blu-ray: 50 GB DL or 25 GB standard
Access times	Full stroke DVD: < 200 ms (seek) Full stroke CD: < 200 ms (seek) Blu-ray: < 230 ms seek) Startup time (time to drive ready from tray loading): BD-ROM (SL/DL): 255/285 BD-R (SL/DL): 255/285 BD-RE (SL/DL): 255/285 DVD-ROM (SL/DL): 255/255 DVD-R (SL/DL): 255 DVD+RW: 255 DVD+RAM: 455 CD-ROM: 155
Maximum data transfer rates	CD-ROM: CD-ROM, CD-R up to 24X CD-R up to 24X CD-RW up to 24X DVD-ROM read CD-ROM, CD-R up to 24 X CD-R up to 24 X CD-RW up to 24 X DVD-RAM up to 8 X DVD+RW up to 8 X DVD-RW up to 8 X DVD+R DL up to 8 X DVD-R DL up to 8 X DVD-ROM up to 8 X DVD-ROM DL up to 8 X DVD+R up to 8 X DVD-R up to 8 X Blu-Ray DVD-ROM DL up to 8 X DVD+R up to 8 X DVD-R up to 8 X BD-ROM up to 6 X BD-ROM DL up to 6 X BD-R up to 6 X BD-R DL up to 6 X BD-RE SL/DL up to 6 X BD-RE TL 4.8 X
Power	Source: SATA DC power receptacle DC power requirements: 5 VDC ± 5%-100 mV ripple p-p DC current: 5 VDC - 900 mA typical, 200 mA maximum
Operating environmental (all conditions non-condensing)	Temperature: 5° to 50° C (41° to 122° F) Relative humidity: 15% to 80% Maximum wet bulb temperature: 29° C (84° F)
Operating systems supported	Windows 8 32-bit and 64-bit Windows 7 Professional 32-bit and 64-bit Windows Vista Business 64 Windows Vista Business 32 Windows Vista Home Basic 32 Windows 2000 Windows XP Professional or Windows XP Home 32 Red Hat Enterprise Linux(RHEL) WS4**, 5, 6 Desktop/Workstation SUSE Linux Enterprise Desktop 10 and 11
Kit contents	HP Blue Laser RW Drive, Cyberlink Power2Go Software, Cyberlink PowerDVD Software, installation guide

HP SD media card reader

Specification	Description
Description	Supports hardware ECC (Error Correction Code) function Supports hardware CRC (Cyclic Redundancy Check) function Supports MS 4-bit parallel transfer mode Supports MS-PRO 4-bit parallel transfer mode Supports MS PRO-HG Duo 4-bit parallel transfer mode Supports SD 4-bit parallel transfer mode Supports UHS-104 SD 4-bit card (version 3.0) Supports CF v6.0 with PIO mode 6 and Ultra DMA 7 mode
Interface type	USB 3.0 high-speed interface
Dimensions (W x H x D)	124.5 x 101.6 x 25.4 mm (4.9 x 4 x 1 in). Fits conveniently in the 5.25 in drive bay.
Supported media types	CompactFlash Type I CompactFlash Type II Microdrive Secure Digital Card (SD) Secure Digital High Capacity (SDHC) SD Extended Capacity Memory Card (SDXC) SD Ultra High Speed II(SD UHSII) Memory Stick Memory Stick Select Memory Stick Duo (MS Duo) Memory Stick PRO (MS PRO) Memory Stick PRO Duo (MS PRO Duo) Memory Stick PRO-HG Duo MagicGate Memory Stick (MG) MagicGate Memory Stick Duo These additional media types are supported with a card adapter. Memory Stick Micro (M2) miniSD miniSD High Capacity Micro SD Memory Card (MicroSD) Micro SD High Capacity Memory Card (MicroSDHC) Test parameters/conditions - power applied, unit operating on system ±5%
Operating systems supported	Windows 8 Pro (64-bit) Windows 8.1 (64-bit) Windows 8 (64-bit) Windows 7 Ultimate (32-bit) Windows 7 Ultimate (64-bit) Windows 7 Professional (32-bit) Windows 7 Professional (64-bit) Windows 7 Home Basic Windows 7 Home Premium (32-bit) Windows 7 Home Premium (64-bit) Windows Vista Business 64 Windows Vista Business 32 Windows Vista Home Basic 32 Windows XP Professional Windows XP Home 32
Kit contents	Media card reader, 5.25 in bracket/rails/bezel, install guide, IO and security software and documentation CD USB-IF, WHQL, compliant with USB Mass Storage Class Bulk only Transport Specification Rev. 1.0, compliant Intel Front Panel I/O Connectivity Design Guide V. 1.3, FCC, CE, BSMI, C-Tick, VCCI, MIC, cUL, TUVT

Controller cards

HP Thunderbolt PCIe 1-port I/O card

Specification	Description
Data transfer rate	Supports up to 20 Gb/s (20,000 Mb/s)
Data rates supported	Thunderbolt certified devices
Bus type	PCIe card, full or half height PCIe slots
Ports	One Thunderbolt 2 external 20-pin output connectors (Rear) one full size DisplayPort input connector (Rear)
Internal connectors	Internal connectors one 5-Pin header connector
System requirements	Windows 7 Professional 64-bit, Windows 8.1 64-bit, Intel i5 series or higher processor, 4 GB RAM, 20 GB Hard Drive, available PCIe slot.
Temperature	Operating: 10° to 55° C (50° to 131° F) Non-operating: -30° to 60° C (-22° to 140° F)
Relative humidity	Operating: 20% to 80%
Compliances	FCC Part 15B, cULus 60950, CE Mark EN55022B(1995)/EN55024-1998 STD, Taiwan BSMI CNS13438, Korea MIC
Operating systems supported	Windows 7 Professional 64-bit, Windows 8.1 64-bit
Kit contents	HP Thunderbolt 2 PCIe 1-port I/O Card, full height and half height bulkhead bracket, DisplayPort cable, GPIO (General-Purpose Input/Output) cables(2), Installation documentation and warranty card.

Networking and communications

Integrated Intel I219LM PCIe GbE Controller (Intel vPro with Intel AMT 11.0)

Specification	Description
Connector	RJ-45
Controller	Intel 1217LM GbE platform LAN connect networking controller
Memory	3 KB Tx and 3 KB Rx FIFO packet buffer memory
Data rates supported	10/100/1000 Mbps
Compliance	802.1as/1588, 802.1p, 802.1Q, 802.3, 802.3ab, 802.3az, 802.3i, 802.3u, 802.3z
Bus architecture	PCI Express and SMBus
Data transfer mode	PCIe-based interface for active state operation (S0 state) and SMBus for host and management traffic (Sx low power state)
Power requirement	Requires 3.3 V (integrated regulators for core Vdc)
Boot ROM support	Yes
Network transfer mode	Full-duplex; half-duplex (not supported for the 1000BASE-T transceiver)
Network transfer rate	10BASE-T (half-duplex) 10 Mbps 10BASE-T (full-duplex) 20 Mbps 100BASE-TX (half-duplex) 100 Mbps 100BASE-TX (full-duplex) 200 Mbps 1000BASE-T (full-duplex) 2000 Mbps
Management capabilities	vPro, WOL, auto MDI crossover, PXE, iSCSI Boot, Muti-port teaming, RSS, ACPI, Advanced cable diagnostic, loopback modes, AMT 9.0 support, Circuit Breaker, VLAN, Multicast Listener Discovery (MLD)

Adapter/transceiver

Specification	Description
HP X520 10GbE dual port adapter	Hardware certifications: FCC B, UL, CE, VCCI, BSMI, CTICK, KCC
HP 10GbE SFP+ SR transceiver	Operating temperature: 0° C to 45° C (32°F to 113°F) Operating humidity: 0% to 85%, noncondensing Dimensions (H x W x D) : 1.19 x 1.38 x 5.57 cm (0.47x 0.54 x 2.19)

Intel 8260 802.11 a/b/g/n/ac PCIe WLAN NIC

Specification	Description
Operating humidity	Operating: 10% to 90%, noncondensing Non-operating 5% to 95% (non-condensing)
Dimensions (H x W x D)	Native HMC: 26.8 x 30.0 x 2.4 mm Carrier card assembly 84 x 119 mm (3.3 x 4.7 in)
Kit contents	PCIe x1 card with full height bracket, rf antenna, antenna cable, separate low profile bracket, software CD and warranty.

Physical features

Feature	Description
Dimensions (W x H x D)	170 x 399 x 442 mm (6.7 x 15.7 x 17.4 in)

note:
HP Cloud Recovery download tool (Cloud Recovery Client) is available under Software and Drivers section on the support page.

HP Z240 Tower Workstation Specifications

Product image

System board

Physical security and serviceability

BIOS

Manageability

Processors

Storage/hard drives

SATA Hard Drives for HP workstations

500 GB SATA 7200 rpm 6 Gb/s 3.5-in HDD

1 TB SATA 7200 rpm 6 Gb/s 3.5-in HDD

2 TB SATA 7200 rpm 6 Gb/s 3.5-in HDD

3 TB SATA 7200 rpm 6 Gb/s 3.5-in HDD

128 GB SATA 6 Gb/s SSD

4TB SATA 7200 rpm 6 Gb/s 3.5-in HDD

500 GB SATA 7.2 K SED SFF HDD

1 TB SATA 7200 rpm 6 Gb/s 3.5-in HDD (hybrid)

HP Solid State Drives (SSDs) for workstations

HP 256 GB SATA 6Gb/s SSD

HP 256 GB SATA 6Gb/s SED Opal 2 SSD

HP 512 GB SATA 6Gb/s SSD

HP 1 TB SATA 6Gb/s SSD

PCIe SSDs for HP workstations

HP Z turbo drive G2 128 GB SSD

HP Z turbo drive G2 512 GB SSD

Graphics

Integrated Intel HD graphics

NVIDIA NVS 310 512 MB graphics

NVIDIA NVS 315 512 MB graphics

NVIDIA NVS 315 1 GB graphics

NVIDIA NVS 510 2 GB graphics

AMD FirePro W2100 2 GB

NVIDIA Quadro K420 1 GB Graphics

NVIDIA Quadro K620 2 GB Graphics

AMD FirePro W5100 4 GB

NVIDIA Quadro K620 4 GB Graphics

AMD FirePro W7100 8 GB graphics

NVIDIA Quadro K4000 8 GB Graphics

Optical and removable storage

HP Slim DVD-ROM Drive

HP Slim SuperMulti DVDRW SATA drive

HP slim Blu-ray writer

HP SD media card reader

Controller cards

HP Thunderbolt PCIe 1-port I/O card

Networking and communications

Integrated Intel I219LM PCIe GbE Controller (Intel vPro with Intel AMT 11.0)

Adapter/transceiver

Intel 8260 802.11 a/b/g/n/ac PCIe WLAN NIC

Physical features

Additional support options

Enter a topic to search our knowledge library